Micro Jig Handle Bridge for GRR-Ripper Adjustable Push Block

[Shop Now !!!]

Intended for use with the GRR-Ripper Adjustable Push Block (sold separately Rockler #62689).

Micro jig handle bridge provides four contact points to apply more downward pressure across the entire width of the GRR-Ripper body for better control. Also includes replaceable push foot.[]

[Compare Product Price!!!]

[Customer Reviews!!!]

[Shop Now !!!]

Leecraft CR-2 Sears Older 10-Inch Belt-drive Zero Clearance Table Saw Insert

[Shop Now !!!]

CR-2 is 14-3/8" x 3-3/4" x 3/16" and fits Sears CRAFTSMAN older 10 belt-drive saws including models: 113.29901 113.29903 113.299040 113.29943 113.299142 113.29960.

• Supports work right up to the blade


• Greatly reduced chip-out and splintering


• Elimantes dangerous gap around blade where thin off-cuts can get wedged

[Compare Product Price!!!]

[Customer Reviews!!!]

[Shop Now !!!]

Magswitch Pro Magnetic Table Featherboard 30mm

[Shop Now !!!]

Switchable Magnetic Table Featherboard
Fast easy setup
Precise positioning
Perfect for infeed/outfeed applications
Easily turns magnets on and off and provides powerful control
Lock the featherboard tight with just the twist of a knob
Use for infeed/outfeed - your work stays in one place firmly
Use with table saw fence on left side of blade
Operation: Align the featherboard with the material to be cut. Use one hand to apply pressure and the other to switch the magnets on. Position the featherboard so it doesn't pressure the saw blade. Leave Magswitch off when done.

• Versatile - no miter slot limitation


• Fast accurate positioning


• Cut wider material


• Can be place beyond the miter slot


• Easy on/off operation

[Compare Product Price!!!]

[Customer Reviews!!!]

[Shop Now !!!]

Micro Jig GRR-Ripper Basic 3D Push Block System (GR-100)

[Shop Now !!!]

The GRR-Ripper lets you feed both sides of a workpiece parallel through the saw blade and eliminates bare hand feeding. It's perfect for ripping thin strips safely. It results in a perfectly straight cut and keeps your hands away from the cutting elements. With grooved non-slip pads on bottom and adjustable handle.

• Lets you feed both sides of a workpiece parallel through the saw blade


• Perfect for ripping thin strips safely


• Achieve perfectly straight cuts while protecting your hands


• Grooved non-slip pads on bottom and adjustable handle

[Compare Product Price!!!]

[Customer Reviews!!!]

[Shop Now !!!]

DEWALT DW7028 Miter Saw Stand Extension Support

[Shop Now !!!]

Includes Miter Saw Stand Extension Support - DW7028

• Extension support supports miter saw stand extension for more rigid support


• Adjustable height from 21-Inch to 37-Inch provides level support on uneven surfaces


• Compatible with dw723 dwx723 and dwx724 miter saw stands

[Compare Product Price!!!]

[Customer Reviews!!!]

[Shop Now !!!]

MasterGage MP-1 MasterPlate

[Shop Now !!!]

Align calibrate and tune up your table saw to within +/- .001". this double disk ground aluminum late fits 5/8" and 1" arbors. Measuring 6" x 10" it's designed for squaring and aligning your saw blade to the table and unlike saw blades it has zero runout! Precisely measure any angle too!

• The MasterPlate is a solid 6-by-10-by-1/4-Inch thick aluminum "tool makers" quality plate ground flat to within thousandths of an Inch


• The MasterPlate provides a full flat 10-Inch surface parallel to the miter slot and a vertical height of almost 7-Inch perpendicular to the table top


• Fits both 5/8 and 1-Inch diameter arbor shafts


• Set both miter and bevel angles on saws to within minutes of a Degree


• Use the MasterPlate to calibrate and troubleshoot table saws radial arm saws chop saws and sliding compound miter saws

[Compare Product Price!!!]

[Customer Reviews!!!]

[Shop Now !!!]